Documented
Purpose, measurement role and operating boundary are recorded.
DEFINEDSO-EMS MASTER R&D PROJECT
Module Registry
SO-EMS is organized as one modular research architecture rather than a collection of disconnected experiments.
M01 establishes the measurement foundation. Each later module can then extend measurement, logging, analysis, storage, recovery, control or system integration while remaining part of the same energy-accounting framework.
M01
M02
M03
M04
M05
M06
M07
M08
M09
M10
ONE MASTER SYSTEM
Every module should strengthen the same measurement architecture.
New modules should not create isolated datasets or incompatible measurement methods.
Each module should contribute to our ability to understand energy input, output, storage, recovery, losses and operating conditions.
MODULE STATUS
Define before we claim.
Only modules with a documented purpose and architecture should be treated as formally defined.
Development
Architecture exists and physical implementation is being developed.
DEVELOPMENTPlanned
Position in the master architecture exists, but the detailed specification is not yet published.
PLANNEDValidation
Physical module is being tested against defined measurement requirements.
TEST REQUIREDMODULE 01
M01 — Energy Meter
M01 is the foundation of the entire SO-EMS architecture.
It establishes the low-voltage DC measurement bench used to record voltage, current, instantaneous power and accumulated watt-hours.
Later modules should be built on measurement principles validated here.
Open M01
SO-EMS M01
Energy Meter
DEVELOPMENT
MODULES M02–M05
Extend the foundation.
These modules remain part of the master architecture. Their detailed roles will be published individually as we restore and formalize their original definitions.
Module M02
Reserved for the next defined SO-EMS measurement or energy-management subsystem.
SPECIFICATION NEXT Open M02 →Module M03
Third module within the unified Sustainable Oasis Energy Management System.
SPECIFICATION NEXT Open M03 →Module M04
Position reserved in the master architecture for a documented measurement or integration function.
PLANNEDModule M05
Position reserved for the fifth defined layer of the SO-EMS system.
PLANNEDMODULES M06–M10
Advanced SO-EMS expansion.
M06 through M10 remain inside the same master R&D structure and will be documented without changing the underlying energy-accounting principles established by M01.
Module M06
Reserved advanced subsystem within the unified SO-EMS research architecture.
R&DModule M07
Reserved for continued expansion of measurement, analysis or physical-system integration.
R&DModule M08
Future module maintained within the same standardized data and measurement architecture.
R&DModule M09
Future advanced integration layer for the SO-EMS master project.
R&DModule M10
Final module in the current ten-module SO-EMS master architecture.
R&DCOMMON ARCHITECTURE
Every module should speak the same energy language.
INPUT
PROCESS
OUTPUT
STORAGE CHANGE
LOSSES
RECOVERY
Consistent Units
Prefer watts and watt-hours for electrical power and energy accounting.
Timestamps
Measurements should retain enough time information to reconstruct the test.
Source Classification
Preserve whether data is manual, sensor-based, imported or calculated.
Data Classification
Clearly distinguish DEMO, ESTIMATED and MEASURED values.
MODULE DESIGN RULES
Every new module must justify its place.
Purpose
Define what question or system problem the module is intended to address.
Boundary
Define what physical system lies inside the module's measurement boundary.
Inputs
Identify energy, signals and physical conditions entering the module.
Outputs
Identify the measurable physical or digital outputs.
Instrumentation
Specify what is measured and how it will be verified.
Data
Define what information should be logged and retained.
Safety
Define appropriate limits and failure conditions.
Validation
Define how the module's measurements or functions will be tested.
DEVELOPMENT LOGIC
Measurement comes before intelligence.
MEASURE
LOG
VERIFY
ANALYZE
CONTROL
OPTIMIZE
SHARED DATA MODEL
One record format can connect the modules.
Module ID
Identify the module producing or receiving the data.
Test ID
Connect measurements to a specific experimental run.
Timestamp
Preserve when the measurement was recorded.
Value
Store the numerical or state measurement.
Unit
Preserve the physical unit with the value.
Source
Identify whether the value came from a sensor, manual entry, import or calculation.
Data Type
Retain DEMO, ESTIMATED or MEASURED classification.
SO-EMS → CONTROL ROOM
Ten modules can eventually feed one operating view.
The Control Room should not need to understand every piece of experimental hardware directly.
SO-EMS can normalize verified measurements and send useful system-level data into the digital Control Room.
Enter Control Room
CURRENT ENERGY MODEL
Control Room Snapshot
—
Current Control Room values may still be DEMO, ESTIMATED or manually entered. SO-EMS modules will progressively create a path toward instrumented MEASURED data.
MODULE → EXPERIMENT
Modules are instruments. Experiments answer questions.
SO-EMS modules should remain reusable across multiple experiments whenever possible.
MODULE
TEST SETUP
PROCEDURE
EXPERIMENT
DATA
RESULT
MODULE VALIDATION
Every module should earn trust before controlling critical systems.
Bench Test
Test the module under simple known conditions.
Reference Comparison
Compare measurements against a suitable trusted reference.
Repeatability
Repeat identical tests and compare results.
Field Test
Observe performance in a real operating environment.
Integration
Connect validated data to larger SO-EMS and Control Room workflows.
DEPLOYMENT PATH
From bench module to Complete Oasis.
Energy Lab
Validate modules under controlled low-voltage conditions.
Energy Lab →Garage Lab
Connect modules to practical systems and real prototype loads.
Garage Lab →Container Infrastructure
Test modular deployment and repeatable system installation.
Container Workshop →Complete Oasis
Measure integrated energy flows across a larger operating site.
Complete Oasis →NEXT DEVELOPMENT STEP
M01 establishes the meter. M02 extends the architecture.
Before building additional modules physically, their role should be restored and documented with the same clarity as M01.
That keeps the ten-module system coherent as it grows.
SO-EMS M01 → M10